DM860 Stepper Driver
zoom_in
  • DM860 Stepper Driver
  • DM860 Stepper Driver
keyboard_arrow_down

DM860 Stepper Driver

47,50 €
με ΦΠΑ

2 phase Digital Stepper motor driver 

Ποσότητα
check Διαθέσιμο

  • Πληρωμή με κάρτα, PayPal, αντικαταβολή και πληρωμή στο κατάστημα.
Παραγγελίες άνω των 300€ για λόγους προστασίας του καταναλωτή δεν εκτελούνται με την μέθοδο της αντικαταβολής. Πληρωμή με κάρτα, PayPal, αντικαταβολή και πληρωμή στο κατάστημα. Παραγγελίες άνω των 300€ για λόγους προστασίας του καταναλωτή δεν εκτελούνται με την μέθοδο της αντικαταβολής.
  • Δωρεάν αποστολή για παραγγελίες άνω των 100€. 
Δωρεάν αποστολή για παραγγελίες άνω των 100€.
  • Ενδιαφέρεστε για μαζικές αγορές και τιμές. Επικοινωνήστε μαζί μας Ενδιαφέρεστε για μαζικές αγορές και τιμές. Επικοινωνήστε μαζί μας

DM860  is a fully digital stepper drive developed with advanced DSP control algorithm based on the latest motion control technology. Its motor auto-identification and parameter auto-configuration feature offers quick setup to optimal modes with different motors. Compared with other analog or TB6600H chips driver, it can drive a stepper motor at much lower noise, lower heating, and smoother movement. 

test

Product features:

1. power supply voltage DC24-80V or AC18-50V

2. drive current 2.4-7.2A

3. subdivision intensive reading 2-200 subdivision options

4. optical isolation signal input

5. motor noise optimization function

6. can drive any two phase, four phase hybrid stepper motor of below 2.0A phase current

7.20KHz chopper frequency

test

Electrical Specifications:

  • Input power: 24-80v, DC power supply, capacity: not less than 200VA. typical value: DC36V
  • Input current: 2.4A-7.2A, 8 adjustable, resolution 0.5A
  • Drive mode: double machine constant current PWM drive input
  • Insulation resistance: >500M Omega at normal temperature
  • Insulation strength: 500V/ minutes at normal temperature
  • Weight: about 400 grams
  • Environmental requirements
  • Cooling mode: natural cooling
  • Use occasions: avoid dust, oil mist and corrosive gases.
  • Ambient temperature: 0 C -+50 C
  • Environmental humidity: <80%RH, no condensation, no frost
  • Vibration: maximum no more than 5.7m/s2
  • Driver input signal interface function
  • Signal interface
  • Signal pretext
  • PLS+ and PLS- control the positive and negative end of the pulse signal. DIR+ and DIR- are the positive and negative ends of the direction signal. 24V needs 2K resistors
  • A+ and A- connect the positive and negative ends of stepper motor A phase winding, B+ and B- connect the positive and negative ends of stepper motor's B phase winding. When the A.B two phase winding is switched, the direction of the motor can be reversed
  • Motor Interface
  • Using the DC power supply, the working voltage range is suggested to be 20-50VDC, the power supply’s power is more than 100W. According to the actual use, the input is suitable for less than DC 40V
  • Indicator light
  • The driver has two indicators:red and green. The green light is the power indicator. When the drive is in charge, the green light is always on. The red light is the fault indicator. When overvoltage and overcurrent occurs, the red light is on. After the fault is cleared, the red light goes out. When the driver fails, recharging and reusing is needed to remove the fault.

test

test

wiring diagram

test

4708840

Notify me when available

Related Products..

You May Also Like..